Cub Cadet 440 Návod k obsluze

Operator's ManualFinishing Mower 48”, 60” & 72”FM48FM60FM72Cub Cadet Yanmar LLC.P.O. Box 368023Cleveland, OH 44136PRINTED IN U.S.A.Version 2

3 - OPERATIONYou have purchased a three spindle mower designed especially for the mowing ofgrassy areas where a highly professional cut is required wi

rented to someone who has not read the operator's manual and is not familiarwith a rotary mower.5. Always stop the tractor, set brake, shut off t

21.Inspect the entire machine periodically1. Look for loose fasteners, worn or brokenparts, and leaky or loose fittings.22.Use only the driveline supp

3.03 - Cutting Height AdjustmentWARNING: Keep hands and feet away from moving blades.Be sure tractor engine is off, parking brake is locked, and key i

3.04 - Pre-Operational CheckCheck each of the following, carefully, prior to engaging the equipment:1. The spindle bearings have been greased.2. The b

To attach the mower to the tractor do the following: 1. Back the tractor up to the mower in order to slip the tractor hitch arms over thehitch pins we

7. Checking to ensure that the cutting edge is the leading edge of the blade6.8. Checking that there is no wire, weed, grass or other material wrapped

Always operate PTO at 540 rpm. This is necessary to maintain proper blade speed andobtain a clean cut.Under certain conditions, tractor tires may roll

3.09 - Uneven TerrainDANGER: Be careful of rollover when operating tractor and mower over unevenground.In extremely uneven terrain rear wheel weights,

4 - MAINTENANCEDANGER: Stop engine, lock parking brake and remove key before performing anyservice or maintenance.Never rely on the tractor lift syste

Take note! This safety alert symbol found throughout this manual is used to callyour attention to instructions involving your personal safety and the

14.Never replace hex bolts with less than grade five bolts unless otherwisespecified, i.e., shear bolts8.15.Where replacement parts are necessary for

same amount to the wheel arm grease fittings (see fig. 9). See the drivelinemanufacturer operator's manual for further information on the driveli

Removing or installing bladesIf the mower blades need to be removed, do the following:1. The blade turns in a counter clockwise direction when viewed

DANGER: Proper torque must be used when tightening the blade retaining bolt. Ifthese safety precautions are not followed, the blade could come off dur

delivery, the spring is located in the first position. When the belt stretches after use,adjust the tension by relocating the spring in the other two

To replace the belt do the following:1. Remove belt shields. Clean foreign material from the mower deck and belt area.2. Release spring tensioner to l

In the collapsed position the driveline should be approximately 2" from bottoming out toprevent possible damage to the tractor or implement. When

Before transporting:1. Disengage PTO.2. Shorten tractor top link until top hitch plate is locked.3. Raise machine and lock rock shaft control lever.4.

TABLE 1 - TORQUE SPECIFICATIONSWhen using locks, nuts, increasing torque values by 5%.438590302420M 20309420217295M 18225305155215M 16148200103140M 14

5 - REPAIR PROCEDURESCAUTION: All repair procedures must be done by authorized dealerships. It is notrecommended that untrained individuals perform an

338 - PARTS MANUAL327 - PRE-DELIVERY CHECKLIST316 - TROUBLESHOOTING305.04 - Storage295.03 - Suggested Spare Parts295.02 - Blade Spindle295.01 - Gearbo

1Belts3Washers3Blade bolts3Blades QuantityDescription5.04 - StorageAfter seasonal use it is important to perform the following for prolonged storage:1

6 - TROUBLESHOOTINGWARNING: Be sure tractor engine is off, parking brake is locked, and key isremoved before making any adjustments.Increase ground sp

7 - PRE-DELIVERY CHECKLISTTo the dealer: Inspect the machine thoroughly after assembly to assure it isfunctioning properly before delivering it to the

9 - PARTS MANUALFinishing Mower 48”, 60” & 72”FM48FM60FM72

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 34 CUB CADET YANMAR

-Cap005-1570221Shaft Protection (EC Only)000-8663214Nut D. 12000-3038204Spring Washer D. 12000-1077192Nut D. 10001-523718-Bolt TE 10 x 110000-6349174N

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 36 CUB CADET YANMAR

1Hook Support (EC Only)002-2435311Driveline Hook (EC Only)002-2433302Linking Plate005-6523298Nut D. 10003-0156288Bolt TE 10 x 30000-1278272Nut D. 1000

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 38 CUB CADET YANMAR

4Air Tire000-87974Hard Tire000-8526361Nut D. 8000-1806351Spring Washer D. 8000-3144341Bolt TE 8 x 25009-1446331Cotter Pin D. 2 (EC Only)005-442232Qty.

1 - GENERAL INFORMATIONThank you and congratulations for having chosen our implement.Your new grooming mower is a technologically advanced machine con

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 40 CUB CADET YANMAR

3Disc Spring000-8560213Blade Bolt 000-85592012Bolt TE 10 x 30000-1278193Grease Fitting 002-9036183Nut D. 25000-6698172Nut D. 20000-5507164Flat Washer

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 42 CUB CADET YANMAR

-Spindle Assembly 000-8533313Bearing 6205-Z 000-6634303Spacer 000-8536293Spindle 000-8538283Bearing 6205-ZZ 000-6626273Spring Washer 000-6606263Cover

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 44 CUB CADET YANMAR

2Chain000-8506293Mulching Blade 72”000-6845M3Mulching Blade 60”000-6641M3Mulching Blade 48”000-6795M281Baffling 72”000-87601Baffling 60”011-58251Baffl

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 46 CUB CADET YANMAR

1Gearbox Complete 050-06682Nut M10003-0156264Flat Washer M10000-2034252Bolt 10x120001-5263241Input Shaft with CCW Rotation005-1187231Ring Gear000-889

FM48/FM60/FM72 OPERATOR’S MANUALPARTS MANUAL 48 CUB CADET YANMAR

1PTO Complete 6'948-816B1PTO Complete 5'948-815B1PTO Complete 4'948-814B1Shield Complete 6'503-349B1Shield Complete 5'503-344

Warranty does not cover the following:1. Cleaning, transporting, mailing and service call charges. 2. Normal wear items such as belts, blades, bearing

= Finishing Mower 48”, 60” & 72” FM48, FM60 & FM72==========================Cub Cadet Yanmar LLC.P.O. Box 368023Cleveland, OH 44136

8. Bolt up the top hitch supports to the outside of the front support plates welded tothe front of the deck (see fig. 2). 9. Bolt up the top hitch pla

2 - SAFETY PRECAUTIONSSafety is the primary concern in the design and manufacture of our products.Unfortunately our efforts to provide safe equipment

2.02 - Starting and Stopping1. Be sure that no one is near the machine prior to engaging or while the machine isworking.2. Be sure the tractor is in &

Fig. 4 - Safety Decals; Replace immediately if damaged.SAFETY PRECAUTIONS 9CUB CADET YANMARFM48/FM60/FM72 OPERATOR’S MANUAL